We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Knitting Needle Conversion Chart: US, Metric and UK Sizes Explained

Use this knitting needle conversion chart to match US, metric and UK sizes, plus tips for handling gaps between systems so your gauge stays accurate.

Updated November 2026

A knitting needle conversion chart matches US sizes to metric millimeter sizes and UK sizes, so you can follow a pattern written in a different system. Most conversions are close but not exact, so always check the pattern’s gauge before you cast on.

Why Needle Sizes Don’t Convert Neatly

US needles are numbered by a system that doesn’t map to a single measurement. Metric needles are sized by the diameter of the shaft in millimeters, and UK needles use an older numbering system where a higher number means a smaller needle. Two countries can sell “size 8” needles that are noticeably different widths.

Shopping for one? See our guide: 5 Best Bamboo Needles for Knitting Beginners and Beyond (2026).

Because of this, conversion charts give approximate matches. A US 7 is commonly listed as 4.5 mm, and a US 8 as 5 mm, but manufacturers round and some brands run slightly fine or slightly thick. The chart is a starting point, not a guarantee.

A Basic Conversion Chart

The table below lists the most common matches. Treat each value as a close equivalent.

US size Metric (mm) UK size (approx.)
0 2.0 mm 14
1 2.25 mm 13
2 2.75 mm 12
3 3.25 mm 10
4 3.5 mm 9
5 3.75 mm 9
6 4.0 mm 8
7 4.5 mm 7
8 5.0 mm 6
9 5.5 mm 5
10 6.0 mm 4
10.5 6.5 mm 3
11 8.0 mm 0

What to Do When a Pattern Uses Different Units

The chart only helps if your gauge still matches. Knit a swatch at least 4 inches (10 cm) square on the needle size the pattern suggests, then measure stitches and rows over that square. If your swatch has more stitches per inch than the pattern calls for, your stitches are too tight, so move up a needle size. If you have fewer, go down.

Keep in mind that fiber, tension and how you hold the yarn all affect gauge, so a conversion that worked for one project may need adjusting for the next.

Practical tips

  1. Measure your needle with a metric gauge or caliper rather than trusting the printed size, especially on older or mixed sets.
  2. Write the metric size on a label or in your project notes so you don’t have to convert again.
  3. Always knit a gauge swatch in the yarn and needle you plan to use, then block it before measuring.
  4. If a pattern gives needle sizes in both systems, follow the one it lists first and use the chart only to check.
  5. Keep a small needle gauge tool with your needles so you can confirm sizes quickly while you work.

What We’d Use

A simple plastic or metal needle gauge with both US and metric markings lets you check a needle’s diameter before you start. Look for one that lists millimeters clearly. View on Amazon

A printed or laminated conversion card is handy to keep in your project bag so the chart is always within reach. View on Amazon

FAQ

Is a US 8 the same as a 5 mm needle?

Close, but not exact. A US 8 is commonly listed as 5 mm, and most patterns treat them as interchangeable, but always check your gauge.

Why do my needles not match the chart?

Manufacturers round sizes differently, and older needles can wear. Measuring the shaft with a gauge gives you a more reliable answer than the printed label.

Should I trust the chart over the pattern?

No. Follow the pattern’s gauge. If your swatch doesn’t match, adjust your needle size until it does, even if the chart suggests otherwise.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our knitting guides, checking product details against manufacturer specifications and owner feedback.

About the author

Claire Whitaker
Claire Whitaker

Claire Whitaker writes reviews and buying guides for Passion Knit.